WJMG Has A Quality Management System

The list of references are used to build a QMS but are not limited to only theses Items.

1) ANSI/AWS Z49.1 Safety in Welding, Cutting and Allied Processes

 

Standard for protection of persons from injury and illness and protection of property (including equipment) from damage by fire and explosions arising from welding and cutting.  Guidance for educators, welders, managers, & supervisors in setup and use of welding and cutting equipment, & safe performance of welding and cutting.

2) WJMG (Company) Health, Safety and Environmental (HSE) Manual

Compilation of the Company's HSE Policies, Procedures, Guidelines, Roles & Responsibilities.

3) OSHA Part 1926 Safety and Health Regulations for Construction

Regulations for Construction, Health and Safety requirements in a set of OSHA regulations for both labor & management in the construction industry.

4) American Welding Society (AWS) Safety and Health Fact Sheets

The free PDF documents (online) provide clear help to common safety & health concerns.  Additional details in ANSI/AWS Z49.1.

5) ANSI/AWS B2.1 Specification for Welding Procedure and Performance Qualification

This specification provides requirements for the qualification of welding procedures for steel >100 ksi yield strength. Also provides requirements for the welder performance. 

6) ANSI/AWS D1.1/D.1.1M Structural Welding Code – Steel

Specified welding standard for “structural steel” in construction contracts .  Fabricators use AWS D1.1 Code for design, welding procedures & welders, fabrication, inspection. The Code details the processes, assures quality, when applied correctly and consistently.

7) Code of Federal Regulations (CFRs), CFR 1910.252 Subpart Q

Welding, Cutting and Brazing - General Requirements.  Basic precautions for fire prevention and protection.  Precautions and delineation of the fire protection and prevention responsibilities of welders and cutters, supervisors, outside contractors & management. Refer to Standard for Fire Prevention in Use of Cutting and Welding Processes, NFPA Standard 51B, incorporated by reference.

8) AISC Steel Construction Manual, 15th Edition

Steel construction codes, specifications & standards. Contains the Code of Standard Practice standards.

9) AISC Specification for Structural Steel Buildings (ANSI/AISC 360)

Specification Manual for Structural Steel Buildings (ANSI/AISC 360)

10) AISC Code of Standard Practice Structural Steel Buildings & Bridges (AISC 303)

Framework for acceptable standards when contracting for structural steel. Specific provisions are contained in the contract documents, the existing trade practices are standard customs on industry and are incorporated into the contract.

11) ASTM E23, Standard Test Methods for Notched Bar Impact Testing of Metals

The test methods of impact testing relate specifically to the behavior of metal when subjected to a single application of a force resulting in multi-axial stresses associated with a notch, coupled with high rates of loading and in some cases low temperatures. Results of impact tests on notched specimens, when correlated with service experience, can accurately predict the likelihood of brittle fracture.

12) ASTM A6, Standard Specification for General Requirements for Rolled Structural Steel Bars, Plates, Shapes, and Sheet Piling

General requirements for rolled structural steel bars, plates, shapes, and sheet piling. The steel shall be made in an open-hearth, basic-oxygen, or electric-arc furnace followed by refining metallurgy in a furnace.  Tension tests (UTS & YS) and chemical analysis shall conform to the required mechanical properties (tensile strength, yield strength, elongation, metallurgical structure and composition of each product.

13) ASTM A370, Standard Test Methods and Definitions for Mechanical Tests of Steel Products

Test methods to determine the specified mechanical properties of steel, stainless steel, and related alloy products for the evaluation of conformance of such products to a material specification under the jurisdiction of ASTM as designated by a purchaser in a purchase order.

14) ASTM A673, Standard Specification for Sampling Procedure for Impact Testing of Structural Steel

Method deals with the standard sampling procedures for impact testing of structural steel. Including longitudinal Charpy V-notch testing, two testing frequencies, (H and P), frequency (H) heat testing, and frequency (P) piece testing.

15) AWS 2.4, Standard Symbols for Welding, Brazing, and Nondestructive Examination

Method for specifying welding, brazing, and NDE information by means of symbols, including the examination method, frequency and interpretation.

16) AWS A3.0 Standard Welding Terms and Definitions

A glossary of the technical terms used in the welding industry. Establishes standard terms for communication of information related to welding and allied processes with terminology and nonstandard terms used in the welding industry.

17) API 5CT Casing and Tubing Specification

Technical specifications for steel casing and tubing pipes used for oil wells in petroleum, natural gas industries and engineered structural pilings.   The Specification includes pup joints, couplings and accessory materials, and establishes requirements for product specification levels (PSL-1, PSL-2, and PSL-3). The requirements for PSL-1 are the basis of this standard.

18) American Society of Nondestructive Testing (ASNT) Recommended Practice, SNT-TC-1A

Guidelines for Employer Based Inspection, Personnel Training, Qualification and Certification. 

19) WJMG (Company) NDT Written Practices

In accordance with SNT-TC-1A, Written Practice is required with 3 sections. The employer shall prepare a document with Procedures, Personnel qualifications, Certification of NDT personnel.

20) OSHA CFRs Title 29 Labor 1901

The Code of Federal Regulations (CFR) is the codification of general and permanent rules published in the Federal Register by the Federal Government. Divided into 50 titles that represent broad areas subject to Federal regulation.

21) CFRs Title 29 Labor 1926

SAFETY AND HEALTH REGULATIONS FOR CONSTRUCTION. Publication developed a single set of OSHA regulations for both labor and management within the construction industry.

22) CFR 1910.132 OSHA, Workplace Hazard Assessments

Protective equipment, for eyes, face, head, and extremities, protective clothing, respiratory devices, and protective shields, shall be provided, used, and maintained in a sanitary and reliable condition for chemicals, hazards, or mechanical irritants encountered that may cause injury or impairment of any part of the body through absorption, inhalation or physical contact.

23) 29 CFR 1910.145, Safety Signage

Signs or symbols that indicate and, define specific hazards that could harm workers or the public, or  damage property. Signage intended to cover all safety signs except streets, highways, & railroads.

24) 29 CFR 1910.146, Confined Spaces

Requirements- practices and procedures to protect employees in general industry from hazards of entry into permit-required confined spaces.

25) SSPC-PA 1 "Shop, Field and Maintenance Painting of Steel"

Procedures for the painting of steel surfaces. Broad scope covers specific, general requirements for the application of paint.  Does not provide descriptions of surface preparation, pretreatments, selection of primers, or finish coats.  Provides procedures and methods for application of coating.